car3dparts.

The parts catalog

Find your next part.

Find your fit. Download a free file or choose a maker to print and ship your part.

Reset

122 matching parts

Free files. Made for your car.
Rear Cup-Holder Claw Repair SetC3D–01410
BMWConsole & storage

Rear Cup-Holder Claw Repair Set

It works and fits, but it is sturdier than the original and if you want extra sturdiness, then make it even thicker, because there is still more place for that part. Print the pin as a separate part and glue it together. it will look better, save you time and work better. Please do not re-upload STL or any other mesh version of this project. I upload STEP only, because I want it to be easily editable. Do not poison the internet. For commercial use contact me and I am sure that we can build something cool out of it. Other than that do whatever you like as long as you mention me as the author of the model. Creator reports the replacement fits and works, and supplies separate claw/pin and combined STEP versions. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Door-Sill Trim Panel ClipC3D–01071
BMWBody panels & exterior trim

Door-Sill Trim Panel Clip

Replacement clip for BMW door-sill/entry trim panels. The creator explicitly lists E21, E30, E36, E39, E46, E81/E82/E88, F20, E85 and related applications and identifies genuine BMW clip 51471840960. Verify the receiving-hole and trim thickness before fitting.

Fits 1 Series · E81 / E82 / E87 / E88 · 1 Series · F20 / F21 · 3 Series · E21 +5

M50 / M52 / M54 Engine-Cover Fastener CapC3D–01147
BMWEngine & intake

M50 / M52 / M54 Engine-Cover Fastener Cap

Replacement beauty cap for M50, M52 and M54 engine-cover fasteners, physically shown on the engine. BMWFans identifies the exact component as cap 11121726089 and confirms E34, E36, E38, E39, E46, E53, E60/E61, E65/E66, E83, E85 and Z3 applications. Use engine-bay-rated material and keep it clear of hot or moving parts.

Fits 3 Series · E36 · 3 Series · E46 · 5 Series · E34 +8

Interior Door-Handle Trim BezelC3D–01143
BMWInterior doors & windows

Interior Door-Handle Trim Bezel

Replacement interior door-handle trim bezel for BMW E30, E24, E28 and E23, physically printed and fitted. BMWFans confirms cover 51211876043. Print in a UV- and cabin-heat-resistant material.

Fits 3 Series · E30 · 5 Series · E28 · 6 Series · E24 +1

M52 Clutch Alignment ToolC3D–01382
BMWInstallation & alignment jigs

M52 Clutch Alignment Tool

Clutch center tool for BMW M52 (and other) motor This tool is needed to mount and center the clutch, you can't used standard tool. Work perfectly on my 1998 528i e39 Creator reports successful use on a 1998 E39 528i. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Sunroof Slider-Rail Repair ClipC3D–01158
BMWCabin trim, cargo & roof

Sunroof Slider-Rail Repair Clip

Fourth-iteration replacement for the small slider-rail clip used in creator-listed E36, E39, E46 and E53 sunroofs. The source shows the physical print and a working demonstration. Use heat-resistant material and verify full sunroof travel, anti-pinch operation and water sealing before driving.

Fits 3 Series · E36 · 3 Series · E46 · 5 Series · E39 +1

Rear Cup-Holder Blanking PlateC3D–01356
BMWDashboard & controls

Rear Cup-Holder Blanking Plate

Very basic blanking plate for the E39 BMW 5 Series rear cup holder. The rear cup holder in my E39 BMW has never closed properly and never clipped in properly and EVERY time someone sits in the rear seat it gets kicked. Odd design by BMW as the cup holder keeps the rear air vents in place so when the cup holder falls out so does the air vent. Printed in blue for prototyping! Second design with holes for 2 USB chargers or cigarette lighter sockets. I used the ones with rubber covers from banggood. The clips are very crude. They need a better design as this panel does not like being removed. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Center-Console Latch RepairC3D–01397
BMWConsole & storage

Center-Console Latch Repair

The center console catch broke in my BMW E61. I've removed the remaining plastic and printed this piece. Attach with two screws and it works perfectly again. Print with 100% infill for extra strength. Creator reports a perfect working repair attached with two screws; photographs show the installed E61 console lid. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Climate-Control Button PairC3D–01363
BMWDashboard & controls

Climate-Control Button Pair

I designed it in a blender. Fits cars: BMW X5 E53, 1999-2007 BMW E39 series 5, 1995-2005 I printed it on cr-10 with .4 nozzle and .2 layer height Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39 · X5 · E53

Headliner Retaining ClipC3D–01395
BMWCabin trim, cargo & roof

Headliner Retaining Clip

EDITED! THIS IS THE ACCURATE MEASUREMENTS. FITS PERFECT! LxBxH 30x15x20mmm Broke some clips when i took down some of my headliner, and could not find any so i made drawn and made some. Clips for headliner in BMW E60 an E61. Creator states the revised dimensions fit perfectly after replacing the earlier version. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Touring Left Cargo-Cover CouplingC3D–01415
BMWCabin trim, cargo & roof

Touring Left Cargo-Cover Coupling

This is a replacement part for the BMW 5 Series Touring (F11). It is the sliding clip ("leash" or "dog") located in the D-pillar track that automatically raises and lowers the rear cargo blind (luggage cover) when the trunk is opened. OEM Part Number: 51437232775 Tested on: BMW F11 520d Touring IMPORTANT INSTRUCTIONS 1. FUNCTION: This part slides inside the track of the rear pillar. It is crucial for the automatic retraction of the luggage cover. 2. LEFT vs RIGHT Side: The uploaded file is for the LEFT side. If you need the RIGHT side, simply use the "Mirror" function (along X-axis) in your slicer software. 3. MATERIAL RECOMMENDATION: Because this part moves in a track and bears weight, I strongly recommend printing with NYLON (PA). - Nylon provides the necessary low friction and high durability. - ABS/ASA might work but will wear out faster. - PLA is NOT recommended. 4. PRINT SETTINGS: - Infill: 100% (Solid) for maximum strength. - Orientation: Print in an orientation that maximizes layer adhesion strength for the pulling force. Designed from scratch as a cost-effective alternative to the expensive OEM repair kit. Creator-tested on an F11 520d Touring. The supplied file is the left sliding coupling; mirror on X for the right side. BMWFans identifies genuine BMW 51437232775 as Coupling, left, produced from 2010-06 for F11/F11 LCI European applications including LHD and RHD. Use nylon where possible, not PLA, and verify smooth movement before loading the blind. Verify dimensions against the original component and confirm full operation before regular use.

Fits 5 Series · F07 / F10 / F11 / F18

Rear-Cabin Vent-Grille Repair SetC3D–01360
BMWBumpers, grilles & guards

Rear-Cabin Vent-Grille Repair Set

My BMW E39 was missing some fan grille parts for the rear seats. The CAD drawings have the exact same size as the original parts. So it just depends on how accurate your printer is (I had to sand down some areas). As you can see in the pictures you will also need a small piece of sheet metal that acts as a spring. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Headlamp Upper Mounting-Tab RepairC3D–01407
BMWExterior lighting, cameras & sensors

Headlamp Upper Mounting-Tab Repair

My Driver side tab cracked in half. It would be a party when on the highway/ move excessively on bumps. Mirror it for the driver side !! PRINT WITH SUPPORTS !! There's a hidden pocket in the tab, you wont see the supports but it will make it print. Creator installed the repair after a cracked driver-side tab caused lamp movement; mirror the right-side geometry for the opposite side and verify beam aim after installation. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Rear Window-Regulator BushingC3D–01339
BMWInterior doors & windows

Rear Window-Regulator Bushing

Two-piece repair bushing for the riveted rear window-regulator slider used on BMW E32, E34 and E36. The creator built it for a personal repair so the original rivet can remain in place, and retained the two halves with friction plus an O-ring. Inspect the regulator, lubricate the guide correctly and confirm smooth glass travel before refitting trim.

Fits 3 Series · E36 · 5 Series · E34 · 7 Series · E32

Manual-Console Cup HolderC3D–01408
BMWConsole & storage

Manual-Console Cup Holder

Tool-free front cup holder for BMW E60 and E61 models without the factory front cup holders. It avoids replacing or modifying the dashboard and is compatible with manual-transmission cars. The creator developed four prototypes over three weeks. The model is configured with three perimeters and three top and bottom layers and is sized for 500 ml cans. The test piece was printed in PLA, so do not place hot drinks in it. Taller occupants should check knee clearance because contact can push the storage compartment inward. Verify fit, secure retention, and unobstructed operation before driving.

Fits 5 Series · E60 / E61

Trunk Toolbox NutC3D–01390
BMWCabin trim, cargo & roof

Trunk Toolbox Nut

I used: fibre reinforced ABS 20 % infill 4 outer wall thickness 0,4mm nozzle no support but slower outerwall speed Might also work with generic ABS/ASA/PETG BMW catalog identifies screw plug 71111179444 from 1986-06 with broad BMW toolbox usage; the API fitments reproduce the creator-listed E38/E39/E60/E65/E66 families. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39 · 5 Series · E60 / E61 · 7 Series · E38 +1

Headlamp Adjuster PairC3D–01355
BMWExterior lighting, cameras & sensors

Headlamp Adjuster Pair

These headlamp adjusters are for the BMW E39 series (5-series from 1996 onwards). The originals are made of some material that gets super brittle with age, and pretty much self destruct. Thus making the headlamps aim far too low, and wobble when driving over the slightest dump. BMWs own solution is to supply new lamps as complete units, price probably approaching $1000. To fix, you need to take the headlamp units apart, which is actually quite easy. There are various instructions on the net, The two manual adjusters simply fully unscrew to release. The third adjuster, connected to a motor, is released by turning the exposed 5mm plastic nut 90 degrees (not all variants have this feature). One word of warning: Do not touch the reflectors, they are very easily destroyed by attempts of cleaning. You need one of each of these per side. They will work for the early halogen units, but may need modification for "angel eyes", and I have no idea about Xenon. Note also that the shape is different from the originals. I believe these may be slightly better - the originals were limited by what you could do with casting. For best strength you should ideally print them laying down, but then some s Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Clip-In Gear Knob SetC3D–01335
BMWConsole & storage

Clip-In Gear Knob Set

Four clip-in replacement gear-knob shapes for the BMW E34 and the creator-listed classic BMW chassis. The design was developed around the common BMW latching stem and includes an installed physical example. Confirm the lever's clip profile and preserve full shift travel before driving; the grouped API fitments reproduce only chassis families explicitly listed by the creator.

Fits 1 Series · E81 / E82 / E87 / E88 · 3 Series · E30 · 3 Series · E36 +14

Door-Mirror Adjustment PinC3D–01376
BMWMirrors

Door-Mirror Adjustment Pin

The mirror adjuster on my E39 stopped moving the mirror in left-right direction, however I could still hear the small motor working. After removing the mirror plate, I found a small plastic component broken. Of course you can't buy this part, only the whole assembly (the one where I marked the pins with red arrows) for 100 USD :). Based on the broken component, I copied the part and printed it. It works perfectly!! Please note that if you need this for up-down motion, you will need to mirror the part before printing. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Trunk-Lid Travel BufferC3D–01375
BMWDoors, bonnet, boot & bed hardware

Trunk-Lid Travel Buffer

This is the buffer that the arm on the boot/trunk hits to stop it opening too far, if it cracks (which it will) then ultimately it tries to bend the gas struts. Photo shows a broken one and the print. This is for the RHS looking at the rear of the vehicle. The LHS is identical but mirror image. Print this so it stands on the long edge (hole and pin are horizontal) or the the arm will seperate the layers, there is a lot of force there. I used PETG at 100% infill. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Dual Center-Console Cup HolderC3D–01346
BMWConsole & storage

Dual Center-Console Cup Holder

Dual cup holder installed in the center-console tray of the creator's classic BMW and explicitly released for E32/E34 preservation. It is a distinct two-container layout from the selected single-cup design. Verify tray width, handbrake and selector clearance, and secure the insert so it cannot move under braking.

Fits 5 Series · E34 · 7 Series · E32

Fuel-Cap TetherC3D–01416
BMWDoors, bonnet, boot & bed hardware

Fuel-Cap Tether

This fits a BMW F11 and maybe also other BMW cars from around 2015. If the old cable brakes, this is a replacement of the ring at the cap and the cable. The original ring has to be removed from the fuel cap. Be careful not to brake anything else then the turning ring. Use side cutting pliers or a similar tool. The put the new ring onto the fuel cap. If the ring does not fit you can also adjust the width in the attached model and re-export. I used TPU 95 for the print. Nozzle diameter can be 0.25 - 0.4, all work. I printed with supports but this leaves a rough finish. This also leads to the fact, that the ring does not slide as good as the original one. But overall it works. Don't forget to like if you like. Creator reports the TPU replacement fits and works on an approximately 2015 F11, while noting rough support surfaces can make the ring slide less freely. The editable FreeCAD source is retained for measured adjustment. Do not force the ring or damage the fuel cap. Verify dimensions against the original component and confirm full operation before regular use.

Fits 5 Series · F07 / F10 / F11 / F18

Center-Console Storage Tray SetC3D–01409
BMWConsole & storage

Center-Console Storage Tray Set

Storage-tray set for the center-console recess in BMW E60 and E61 models. Variants include a blank tray for customization, the creator’s everyday layout, a three-coin layout, and a tray for a Hörmann HS M 2/4 garage-door remote with an additional small compartment. The creator reports that the tray fits the existing console recess well. The demonstrated print used Fiberlogy Impact PLA; PETG is also suitable, while ordinary PLA is not recommended for vehicle-cabin temperatures. Verify dimensions, secure retention, and unobstructed operation.

Fits 5 Series · E60 / E61