car3dparts.

2004–2013

3 Series E90 / E91 / E92 / E93

Verified catalog fitment for this exact BMW generation. 49 printable parts currently match.

M57 Self-Adjusting Clutch Alignment ToolC3D–01282
BMWInstallation & alignment jigs

M57 Self-Adjusting Clutch Alignment Tool

This is clutch alignment tool for BMW self-adjusting clutch. I used it on 2007 BMW E93 with M57 engine, but it could be used on other BMWs with SAC. You will need M6 bolt to use this tool. I print it with 50% infill using PETG, but PLA should work just fine, as you shouldn’t need much force to pull the tool out if you installed and torqued everything correctly. It has been printed on Prusa MK3S printer. Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

Fits 3 Series · E90 / E91 / E92 / E93

Air-Vent Louver LinkageC3D–01281
BMWDashboard & controls

Air-Vent Louver Linkage

This connector moves all the louvers in the vent together. Originally is made of metal and super thin. Printed with 100% infill Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Interior Panel-Lock ToolC3D–01279
BMWService tools

Interior Panel-Lock Tool

A little tool I printed to turn those pesky panel locks on my BMW E90 without instead of marring the edges with a big screwdriver. Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

Fits 3 Series · E90 / E91 / E92 / E93

E91 Boot 12-Volt Socket BlankC3D–01277
BMWCabin trim, cargo & roof

E91 Boot 12-Volt Socket Blank

This is a cover to replace the 12v point in the boot/trunk of an E91 ( check for other models similar) with a blank plate. For fitment insert widest plastic tap to top and tap/hammer upwards. Then support the plastic of car from behind and push/hammer in. Push down to seat and stop it falling out. Cleaning up of carpet and plastic edge of hole may be required. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Boot-Lid Handle ReplacementC3D–01274
BMWDoors, bonnet, boot & bed hardware

Boot-Lid Handle Replacement

Hello, since the OEM handle was so expensive i decided to create my own. Let me know what you think. Supports are needed, i used roof support as well. WARNING be careful removing the supports you can break the top sections. Replacement part for OEM BMW handle. Part Number: 51477152356. Supersession(s): 51-47-7-152-356 (This product fits 123 vehicle variants. BMW: 12 models, 123 variants between 2004 and 2013.) BMW E90 Trunk Handle Replacement 2004-2013 by blackjet123 is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License. First Thingiverse make! Let me know if i missed any useful information. Use exterior-rated material and verify secure retention and adjacent-panel clearance.

Fits 3 Series · E90 / E91 / E92 / E93

Factory Phone-Dock Delete TrayC3D–01271
BMWConsole & storage

Factory Phone-Dock Delete Tray

REPLACEMENT TRAY FOR USELESS PHONE CADDY watch this to learn how to remove that useless thing NOT MINE VIDEO ALL THE CREDIT TO THAT GENTLEMAN And then replace it wit the tray enjoy Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

No-Drill Boot HookC3D–01270
BMWCabin trim, cargo & roof

No-Drill Boot Hook

Can be installed in preexisting holes, no drilling necessary. BOM: 2 x M4x10 screws 1 x M4x50 screw 3 x M4 nuts Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Boot Toolkit Reversible Screwdriver HandleC3D–01268
BMWService tools

Boot Toolkit Reversible Screwdriver Handle

BMW Toolkit screwdriver. I designed this for E90 toolkit, as they stopped supplying these in the trunk after E46's. I spent ~$10 for a Phillips/flathead screwdriver from an online OEM supplier. This vehicle uses solely Torx fasteners, so a Phillips/flathead does me no good. This design allows you to use an off the shelf 2" long 1/4" bit extender. Then you can add whatever bit you'd like. Such as any size Torx bit, any size Phillips, or a flathead. It doesn't quite fit in the toolkit, some trimming would be required as the extender is thicker than the stock neck. However it will fit nicely, and the trimming is easy. The extender is a friction fit, but using an 0.2[mm] nozzle, it is TIGHT. It is also worth noting that this screwdriver has a 10mm box wrench on the bottom, and an 8mm box wrench on the top, but you have to remove the extender to use that one. Replaces BMW PN 71111179629 Shoul Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

Fits 3 Series · E90 / E91 / E92 / E93

Non-iDrive Console Can HolderC3D–01266
BMWConsole & storage

Non-iDrive Console Can Holder

Can holder designed for 55 mm Red Bull cans. It is only suitable for cars without iDrive because it occupies the center-console location normally used by the iDrive controller. The creator reports a print time of 12 hours 3 minutes and dimensions of 74.8 × 135.1 × 72.4 mm. Use cabin-heat-resistant material, dry-fit the part, and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Dashboard Air-Vent Lever RepairC3D–01264
BMWDashboard & controls

Dashboard Air-Vent Lever Repair

In my BMW E91 were the Air Vent Levers missing. The original replacements cost a fortune, so i designed some by myself. Print them with PETG or similar. I recommend to print the fork with hinge part. Use the Fork and the Lock File only if you want to print them separately. For the stripe you may want to change the color, so i made it one part for manual color change by a certain height and two parts for MMU printing. You should add a raft under the Leverpart for better bed adhesion on the very small parts lying on the bed. Print them in the provided orientation Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

N47TU Clutch Alignment ToolC3D–01262
BMWInstallation & alignment jigs

N47TU Clutch Alignment Tool

Clutch alignment tool for BMW E90 - engine type n47tu - place some tape around the spindle on the tool to make a firm fitting. Custom designed in TinkerCAD, whipped it up in about 15 minutes after googling the dimensions and worked great!!! Originally bought a kit with multiple sizes of spindle and none of the sizes supplied fitted, so, 3D printed this instead and worked better than spending £25 at my local auto-parts dealer for the kit!! Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

Fits 3 Series · E90 / E91 / E92 / E93

Undertray and Splashguard Plastic NutC3D–01259
BMWBody panels & exterior trim

Undertray and Splashguard Plastic Nut

The is a model of a BMW E90 plastic nut. These nuts are used in the undertray, splashguard and several other places in the vehicle. The nut itself is unthreaded since it is screwed onto a thread cutting fastener. The inner diameter of the nut is 4.25mm. The nut fits a 10mm wrench. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Front Parking-Sensor Aperture PlugC3D–01258
BMWExterior lighting, cameras & sensors

Front Parking-Sensor Aperture Plug

This is my first 3D design. I needed this to plug holes in my bumper without buying parking sensors. It fits nicely, although I used some epoxy glue to be sure it stays in. Use exterior-rated material and verify secure retention and adjacent-panel clearance.

Fits 3 Series · E90 / E91 / E92 / E93

Large Console Cup HolderC3D–01257
BMWConsole & storage

Large Console Cup Holder

The cup holders in my 325i are small and work with anything bigger then a 12oz can. I designed this cup holder fit large insulated tumblers like the Yeti. The top 2 pieces need to be glued together. Gorilla glue works well, but any plastic glue should work. I used a hot glue gun to secure the base to the center console of the car. The hot glue works well and can be removed without any damage to your car. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Console 12-Volt Accessory PlateC3D–01256
BMWConsole & storage

Console 12-Volt Accessory Plate

When I bought my e91 it had no front console cigarette lighter which meant I had to use an after market accessory plugged into the armrest socket. The unit was then wedged between the console and the passenger seat. Less than ideal. This plate fits in the ashtray hole and has a cut-out to accept an after market twin socket adapter which can be commonly found online or in value stores. I desinged this in sketchup and have included the SKP file in case anyone would like to remix it. Happy Printing Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Positive Battery Terminal CapC3D–01255
BMWCabin trim, cargo & roof

Positive Battery Terminal Cap

This is the cap for the positive battery terminal for a BMW E90. It should fit just about any BMW. Use automotive-rated wiring and connectors, retain fuse protection, insulate every terminal and verify unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Pre-LCI Right Headlight Washer CoverC3D–01254
BMWWipers & washers

Pre-LCI Right Headlight Washer Cover

12.03.2019 2mm wider version added. it is suitable for 2005-2009 e90/e91 BMW. it is right side, but you may mirror the item by using Cura's x or y axis mirroring feature. i did not test for left side. But it should be. 3D PRINTING SETTINGS infill %15 layer 0.20mm 0.80mm, perimeter 2, 0.4mm nozzle Please share your photos, i will appreciate to you, it is really important for me. Confirm body and lamp variant, secure retention, weather sealing and legal lamp operation before driving.

Fits 3 Series · E90 / E91 / E92 / E93

Front-Wheel-Arch Headlight Access CoverC3D–01253
BMWExterior lighting, cameras & sensors

Front-Wheel-Arch Headlight Access Cover

Here I leave the headlight cover, located on the mudguard of the front wheel, is a piece very easy to lose and so I leave here the model to be able to print the fleeces own covers. Mine is already 1 month and I have not lost it or left, my BMW is an E91, but I think it serves in all E90 series. I leave the files in solidworks if they want to improve. Good impressions !! Greetings BMW Confirm body and lamp variant, secure retention, weather sealing and legal lamp operation before driving.

Fits 3 Series · E90 / E91 / E92 / E93

325i Clutch Alignment ToolC3D–01252
BMWInstallation & alignment jigs

325i Clutch Alignment Tool

This tool perfectly aligns the clutch friction plate for a BMW E90 325i with dual mass flywheel and self adjusting clutch. On the gearbox side of the tool there is a 7.1mm dia hole so that it can be tapped to M8. I recommend printing in PLA with 100% infill. Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

Fits 3 Series · E90 / E91 / E92 / E93

Bonnet Release HandleC3D–01251
BMWDashboard & controls

Bonnet Release Handle

I broke my bonnet release for my e92 so printed a new one with the BMW logo in it. It is considerably stronger if printed in PETG and it a perfect fit Use exterior-rated material and verify secure retention and adjacent-panel clearance.

Fits 3 Series · E90 / E91 / E92 / E93

Under-Seat Vent GrillesC3D–01250
BMWDashboard & controls

Under-Seat Vent Grilles

The BMW E92 has under-seat air-con vents which are prone to getting small objects kicked down them by rear seat passengers. Worse, there a small gap between them through which coins and the like can end up under the carpet where they then rattle annoyingly. Getting them out is a real pain an requires the seat, and possibly the speaker under it, to be removed. These simple grills clip over the vents preventing small objects going where they shouldn't. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93