Find your next part.

Cup holder with an integral mounting tongue for the centre-armrest compartment. The creator states exact generation fitment and shows the physical print loose and installed, with the tongue pushed beneath the armrest screw. Use cabin-heat-resistant material, avoid damaging the armrest fastener or trim, confirm the lid and selector remain unobstructed and test retention only with a closed cold container before road use.

Fits SLK / SLC · R170

Replacement hinge set for both sun visors, developed from a 2003 car and explicitly stated by the creator for 1998–2004 SLK 230, SLK 320 and SLK 32 AMG models. Source photographs show the visor, original and printed hinges loose, and the completed visor installed. The creator used carbon-fibre HTPLA with 2 mm walls, 30% gyroid infill, supports and post-print annealing. Treat the supplied end-hinge files and combined hinge file as a set, compare every original piece, use tough cabin-heat-resistant material, smooth pivot surfaces and verify each visor holds securely without obstructing vision.

Fits SLK / SLC · R170

Replacement housing for the rear-door magnetic bumper on 2002–2006 vans. The creator cites original reference 901 740 03 16 but explicitly says this geometry is not an exact match; therefore that number is preserved only as a reference and is not assigned. Printing requires a layer pause to encase the reused original metal components, with TPU 64D or 95A specified. Inspect rust expansion, clean and protect the metal parts, confirm door alignment and magnetic retention and verify the housing cannot detach or interfere with complete door latching.

Fits Sprinter · W901–W905

Two-piece cup holder replacing the original dashboard ashtray, explicitly designed for 903-series vans. The creator states that a spring must be added for the mechanism; source imagery shows the installed holder, loose physical parts, mechanism and CAD views. Use cabin-heat-resistant material and a securely retained spring, preserve controls and selector clearance and test only with closed cold containers until retention under braking is confirmed.

Fits Sprinter · W901–W905

Replacement linkage rod for a dashboard air vent, explicitly identified for 901-series vans. Source photographs show the small printed rods and the matching vent assembly, but no steering-side or vent-position split is stated. Compare the original linkage length, pins and grille geometry, use tough cabin-heat-resistant material and verify every vane moves together through full travel without binding or detaching.

Fits Sprinter · W901–W905

Two-material push knob for operating the interior sliding-door latch, developed on a 2006 2500 van after the replacement handle tab failed. The source provides STL and 3MF variants plus photographs of the physical knob, and specifies flexible material sandwiched between rigid sections. Clean and repair a resistant latch mechanism rather than forcing it, use tough cabin-heat-resistant materials, confirm secure engagement and verify normal opening, closing and latching from inside and outside before use.

Fits Sprinter · W901–W905

Replacement holder for the warning triangle in a 903-series van. The creator supplies a printable file and one CAD source image but gives no body-style, market, mounting-fastener or crash-retention details. Compare the triangle case and mounting position, use tough cabin-heat-resistant material, reuse appropriate fasteners and verify the emergency equipment remains secure, accessible and unable to become a loose object.

Fits Sprinter · W901–W905

Four-piece phone-holder system that clips into the dashboard ashtray position, with a phone cradle, left and right support arms and a ball-interface console base. The creator explicitly states 903-series fitment and supplies CAD source views but no installed follow-up photograph. Confirm the ashtray opening, phone dimensions and ball interface, use cabin-heat-resistant material, keep the assembly clear of the selector and controls and verify the phone cannot detach or obstruct the driver under braking.

Fits Sprinter · W901–W905

Replacement limiting arm for the glove-compartment door, made for a 2003 van. The creator supplies an in-vehicle source photograph and a CAD view but no body, steering-side or market expansion beyond that vehicle. Compare the original arm, pivots and door travel, use tough cabin-heat-resistant material, avoid trapping wiring or documents and verify the door opens, closes and latches without overextending.

Fits Sprinter · W901–W905

Replacement bulb socket for the clearance/parking lamp in the headlamp, explicitly identified by the creator as A2108260582 for 208- and 210-series cars. The source provides one author-downloadable STL and one CAD image but no physical fit photograph. Official Mercedes parts-store metadata identifies the exact child as the clearance-lamp socket for CLK 208 and E-Class 210. Verify VIN and headlamp variant, use heat- and flame-resistant electrically insulating material, transfer the correct contacts and bulb without damaging insulation, and test retention, polarity, lamp output, sealing and heat behavior before road use.

Fits CLK · C208 / A208 · E-Class · W210 / S210

Ten-card organizer sized for the eyewear/storage compartment in the centre console. The creator explicitly identifies 210-series fitment and notes compatibility with a separate mini-drawer, but provides only a CAD source image and does not establish other models. Use cabin-heat-resistant material, confirm compartment dimensions and lid travel, and ensure cards remain retained without obstructing the selector or other controls.

Fits E-Class · W210 / S210

Phone tray with an accessory USB charging socket for the rear centre-console cover position. The creator states 210-series use, 3M VHB or Tesa ACXplus adhesive mounting, and supplies the original-cover comparison plus the physical tray; no installed follow-up image is present. Use cabin-heat-resistant insulating material, a fused automotive-grade USB module and strain relief, preserve rear-console and seat travel, and verify adhesion and wiring clearance before use.

Fits E-Class · W210 / S210

Modular replacement for the centre-console ashtray insert, with USB-power and optional 50-cent coin-dispenser configurations. The creator states 210-series fitment, documents an installed dimensional correction, and specifies a 9 x 35 mm spring and adhesive for the dispenser components; source photographs show loose physical assemblies and the wired USB insert. Use cabin-heat-resistant insulating material, a fused automotive-grade USB module and strain-relieved wiring, keep conductors and coins isolated, and confirm selector and console clearances.

Fits E-Class · W210 / S210

Adapter for the original Nokia phone mounting point, intended to accept contemporary phone holders. The creator explicitly identifies 210-series fitment and supplies a photograph of the physical print. Confirm the factory cradle profile and the chosen holder interface, use cabin-heat-resistant material, secure the phone without obstructing controls or airbags, and verify it cannot detach under braking.

Fits E-Class · W210 / S210

Replacement handle for the climate-control panel. The creator states exact 210-series use and provides four CAD views plus a printable part and an editing variant, but no installed photograph or detailed trim/market split. Compare the original handle, shaft and panel before printing, use cabin-heat-resistant material, keep the control mechanism free of debris, and verify full smooth travel and the correct setting indication after installation.

Fits E-Class · W210 / S210

Push-fit mechanical adapter that converts the smaller dashboard lighter opening to accept the larger socket insert shown by the creator. The creator supplies one STL and physical source images but does not state socket current, fuse rating or heat testing. Match the opening and chosen insert, use flame- and cabin-heat-resistant material, retain the original fused circuit limits, insulate all terminals, keep the socket clear of adjacent controls and stop use if the print softens, loosens or heats.

Fits C-Class · W202 / S202

Support for the interior third brake lamp, shown as a physical print and fitted at the base of the rear window. The source does not state body-style, market or production-break coverage, so compare the lamp, parcel shelf and rear-glass profile before printing. Use UV- and cabin-heat-resistant material, preserve the full illuminated area and wiring clearance, secure the lamp against vibration and verify operation and rear visibility before road use.

Fits C-Class · W202 / S202

Storage-bin replacement for the factory ashtray opening. The source notes that light from the original ashtray bulb can shine through light-coloured material and supplies one STL with source renders. Use opaque cabin-heat-resistant material if light bleed is undesirable, compare the ashtray opening and lamp clearance, deburr the edges and confirm the bin and stored items cannot interfere with the selector, controls or occupants or become loose under braking.

Fits C-Class · W202 / S202

Replacement pneumatic coupling for the vacuum-operated headlamp height adjustment, developed for a C180 after the original connector broke and leaked. The creator sealed the printed part with nail polish to make it airtight. Match both hose and headlamp ports, use fuel/oil/heat-resistant material suitable for engine-bay vacuum service, seal without obstructing the passages, leak-test the system and verify both lamps adjust and remain correctly aimed before night driving. The moulded fragment “012502” is preserved as evidence but is not treated as a complete Mercedes part number.

Fits C-Class · W202 / S202

Small retaining pin used by the creator to mount a threshold/door-sill trim panel on this vehicle generation. Source images show the printed pin beside original-style pins and at the sill mounting points. Compare the original pin, panel hole and body socket before printing; use a tough cabin- and weather-resistant material, remove sharp edges, press-fit without forcing brittle trim and confirm the sill panel is fully retained and cannot foul the door.

Fits C-Class · W202 / S202

Phone holder made for a Samsung Galaxy Note 4 and shown physically installed across the centre dashboard vents. Confirm the phone dimensions, vent geometry, hazard/control access and sight lines before use. Print in cabin-heat-resistant material, deburr all contact surfaces, avoid loading fragile vent vanes and verify the phone cannot detach, obscure the road or interfere with controls or airbags under braking.

Fits C-Class · W202 / S202

Cup holder for a cassette-deck opening, tested by the creator in this vehicle generation with 12 oz and 16 oz UK cups. Two OBJ variants are supplied: zero degrees and 25 degrees; the creator states the 25-degree version keeps a drink upright in this cabin. The stereo must remain in cassette-eject mode while fitted. Use cabin-heat-resistant material, verify the deck supports the holder without damage, keep liquids away from electrical controls and occupants, and test retention with a cold, closed container before road use; hot liquids and abrupt braking can cause burns or electronic damage.

Fits C-Class · W202 / S202

Front-door speaker adapter for shallow 160–170 mm drivers; the creator used a 50 mm-deep Pioneer driver. The supplied geometry is for the right/passenger side and must be mirrored for the left/driver side. The source specifies no supports, 0.3 mm layers, 0.8 mm walls and 30% infill, and requires drilling a small wire hole and sealing it after routing. Match the speaker basket and door mounting pattern, use cabin-heat- and vibration-resistant material, protect wiring, seal the wire opening and confirm both adapter and driver remain secure without interfering with glass or trim.

Fits C-Class · W202 / S202

Original-style and gusset-reinforced replacement variants for the sprung latch inside the center-armrest storage cubby, with creator-stated fitment for 1992–1999 vehicles. The creator also states that mirroring the geometry makes it work for the glove-box latch in the same generation. The source photograph shows the physical latch mechanism and child piece. Independent inspection found the gusseted STL non-watertight, so repair and validate that mesh before slicing. The author reports that commissioned ABS versions lasted about 18 months despite embedded steel wire and changed to SLM 316L stainless steel for expected long-term durability. If printing in polymer, use a tough cabin-heat-resistant material, keep a spare, and verify reliable spring engagement and positive latching before use. Work over a clean surface to avoid losing the original spring; a replacement spring may require a carefully filed groove in the post.

Fits S-Class · W140 / C140