Find your next part.

Isofix cover for BMW E46 I was missing one of the isofix covers so I modeled and printed this one. It's not a perfect copy since I added a bit of thickness in some parts to make it stronger. You can see in one of the images the differences between the original and the 3d printed part. For this one the ABS filament is required since the PETG & PLA are not rigid enough. Added a magnetic version, magnet can be glued in place, 20 x 10 x 3 mm magnet size. This alleviates the need to print the part in ABS for strength. Print Settings Printer: TwoTrees Bluer Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Filament: Generic ABS Black Notes: Category: Automotive Confirm seat movement, belt access and occupant clearance before use.

Fits 3 Series · E46

This is a nut for the engine cover as seen in the second image. It works for e46 316i,318i and 320i, possibly for other models that have the same nut. Note: you will need an O-ring or rubber washer (⌀10mm) to prevent unscrewing due to the engine vibrations, the original nut has one too. You'll need ABS filament or PET-G, PLA filament will break after a couple of months. Print Settings Printer Brand: Artillery Printer: Artillery Hornet Rafts: Yes Supports: No Resolution: 0.2 Infill: 25 Filament: ABS or PET-G Notes: minimum 3 perimeter for Vertical shells Category: Automotive Use the specified automotive-grade material, keep the tool square and inspect the serviced component before reassembly.

Fits 3 Series · E46

Seals for the BMW E46 320i Touring for the roof rails. Print settings: Material: Filaflex Semisoft Supports: No Layer height: .3 Infill: 40% Use exterior-rated material and verify secure retention, sealing and adjacent-panel clearance.

Fits 3 Series · E46

Cut off the remains of the rubber part on your windshield cowl and attach these printed ones. OEM PART: 51718208483 Mirror the end part to use it on the other side. Print multiple mid parts to cover the entire length. Printed from Fillamentum Flexfill 89A. Using 0.15mm layer height is important as there is a steep overhang on the part, which wouldn't print well using thicker layers. The end part might not fit perfectly but it did the job already so I didn't tweak it anymore. Use heat-, UV- and fluid-resistant material and verify full wiper or washer clearance.

Fits 3 Series · E46

This is a remixed version of the original thing posted here on Thingiverse, which is a shift boot bracket for the BMW E46 3 Series. It has better strength as with the added fillets and the clips are thickened as well as enlarged for better fitment. It will fit both RHD and LHD BMW E46 and will provide tight fitment. If you are planning to install with thick Alcantara leather boot, then it will be wise to scale it down a bit to 96-97% scale but if you are just planning to use faux leather boot, then at 100% scale it will be just fine. Use custom support blockers to increase the infill density of the clips to 99% for added strength. Print it in ABS or PETG because PLA will definitely deform du Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Replacement air-intake suction tube for 1999-2001 E46 M52 models, physically installed by the creator. BMWFans, RealOEM and Hubauer cross-confirm genuine BMW component 13711438768 for the matching E46 320i/320Ci, 323i/323Ci and 328i/328Ci applications. Print in a heat-resistant engine-bay material and verify sealing and clearance.

Fits 3 Series · E46

My dog rides shotgun and would always step on the hazard button when getting in and out, or when I left him in the car. I made this button cover to prevent paws from being able to activate the buttons, but still allow a finger to hit them easily. This is a friction fit in my car and doesn't move around at all. I sanded the top surface in the main picture. source openscad file is attached. Print Settings Printer Brand: PowerSpec Printer: PowerSpec 3D Pro Rafts: No Supports: No Resolution: 0.2mm layer height Infill: 20% Notes: printed upside down Post-Printing I sanded the top surface to make it a matte finish so it doesn't stick out in the car. Category: Automotive Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Four-piece repair for the broken mounting tab on the pre-facelift E46 tail-light bulb holder. The creator physically tested it on a 1999 E46 320i with amber turn signals and documents the M6/M3 hardware and left/right external plates. Confirm body and lamp variant, secure every fastener, and verify weather sealing and legal lamp operation.

Fits 3 Series · E46

This is for installing a new center support bearing on your E46 driveshaft without risking damaging the bearing. Simply apply some lubricant where the bearing will seat onto the driveshaft and slide bearing on. Then use the tool to hammer in the bearing. It is easier to do with 2 people or if you can stand up and balance the driveshaft with your legs (Ask me how I know). Use the specified automotive-grade material, keep the tool square and inspect the serviced component before reassembly.

Fits 3 Series · E46

I used this tool to remove the crankshaft seal on the M54 engine timing cover. To use it properly, you must place the removal tool from the inside of the timing cover, pushing the seal out towards the outside of the timing cover. Use a mallet and some patience to get it out. Use the specified automotive-grade material, keep the tool square and inspect the serviced component before reassembly.

Fits 3 Series · E46

replacement interior hood latch, original often breaks this version is way stronger than the original Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

BMW E46 Headlight washer cap (left side) BMW part number: 6167.8.256.179 Verify secure retention, weather sealing and legal lamp operation before driving.

Fits 3 Series · E46

These clips can be glued in your oval mirror housing of a BMW E39 M5 or E46 M3 to repair the broken ones. Use "crazyglue" and line the clips up with the missing tabs in the housing. See photos for reference. Dry-fit before fastening and verify glass, latch, wiring and trim clearance through full operation.

Fits 3 Series · E46 · 5 Series · E39

5mm Cable Holder Headlight Bracket Wiring Harness Trim Clip cable clips used to hold the headlight wiring under the hood, redesigned to be easy printable OEM: 61138350827 Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

All 3 parts on my Cults profile: 3D MODEL DESCRIPTION Side BMW E46 interior mounts for windshot. All 3 parts are combinable with the original parts, so you dont have to print all 3 parts and you can choose only these you need. 3D PRINTING SETTINGS I printed in PETG - original settings. Automaticaly generated supports in Prusa Slicer are totally ok to remove. After printing, I recommend to lubricate screw with the nut before tightening. PLA will not be durable enough for outside conditions, so PETG, ABS or ASA are ideal options. Use exterior-rated material and verify secure retention, sealing and adjacent-panel clearance.

Fits 3 Series · E46

Coloring the m logo will make it way better! Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Print standing vertically, Coat with a clear Just glue on your trim and push it on Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Hello this is an alternative sliding cover for rear console ashtray in an e46. Both my brothers and my e46 were missing the covers and its a bit of a pricey piece to replace for what it is. I printed in PLA+ with layer lines running against the slats to prevent breakage. Id recommend something like PETG but so far so good in our cars! Included is a 10min test piece file to check fitment and flexibility of your material. You can bend bottom of the cover gently to the curve of the slot before inserting first time to make it go in smooth. If the top of the cover with handle isnt flush when first installed you can bend it up a bit until its flat. I did what I had to do make it work with PLA+ so Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

i bought RHD mirrors to my LHD e46 non-M Coupe and I created this raisers in order to get a better view angles (close to regular mirrors). This can be use to rise the angle of either side of the mirror and can be used in both mirrors. So with this you can "transform" RHD to LHD and viceversa. Dry-fit before fastening and verify glass, latch, wiring and trim clearance through full operation.

Fits 3 Series · E46

Greetings. At the moment, the model has already been strengthened and differs from the photo! There was a lot of window play in my E46. the glass rose heavily and crookedly. after disassembling the power window, it became clear that there was strong wear and tear and a large backlash. The brace does not come as a separate spare part, and you cannot buy an official one separately. My model is not perfect, it is robust, reinforced. Copes with its function. Window regulator carriage, right door, farthest from the motor v7. home plate (m) the following model, using the native metal plate in the link Dry-fit before fastening and verify glass, latch, wiring and trim clearance through full operation.

Fits 3 Series · E46

Cupholder insert for the rear armrest of BMW E46. The backing is inserted under the leather. Use the backing to mark the location for your cuts. A single slit in the center "web" is also needed to get the backing into the armrest. Carve out the foam as needed to clear the cupholder. Insert the backing, insert the cupholder and use 6 wood screws to hold them together. The screws I used have 4mm outer thread. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Many of these filters for the windshield washer reservoir get's broken and fall down into the water. The design is using the filter of the old holder and fits nice into your windshield water reservoir. Cut of the filter from the old holder. Glue it on the bottom. Cut off everything protruding. Done! The bar helps you to get the filter out for cleaning. Use heat-, UV- and fluid-resistant material and verify full wiper or washer clearance.

Fits 3 Series · E46

Replacement upper retaining clip for the rear front-seat back panel, modeled from the surviving seat-panel clip profile and physically compared with the panel. The nearby V5BB Brombeer catalog number identifies the complete parent panel and is intentionally omitted. Confirm seat movement, belt access and occupant clearance before use.

Fits 3 Series · E46

The carpeted panel on the interior of the E46 touring hatch is tricky to remove, and often the retaining clips are broken. I have created these two clips which can be epoxied in place to return normal function. In order to use them, completely cut the broken part of the clips out as shown in the photo then, use an epoxy like JB Weld liberally - the holes provide a mechanical bond for the epoxy. Note there are a right and a left. I did not create the center clip. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46