car3dparts.

The parts catalog

Find your next part.

Find your fit. Download a free file or choose a maker to print and ship your part.

Reset

260 matching parts

Free files. Made for your car.
Front Parking-Sensor Aperture PlugC3D–01258
BMWExterior lighting, cameras & sensors

Front Parking-Sensor Aperture Plug

This is my first 3D design. I needed this to plug holes in my bumper without buying parking sensors. It fits nicely, although I used some epoxy glue to be sure it stays in. Use exterior-rated material and verify secure retention and adjacent-panel clearance.

Fits 3 Series · E90 / E91 / E92 / E93

Large Console Cup HolderC3D–01257
BMWConsole & storage

Large Console Cup Holder

The cup holders in my 325i are small and work with anything bigger then a 12oz can. I designed this cup holder fit large insulated tumblers like the Yeti. The top 2 pieces need to be glued together. Gorilla glue works well, but any plastic glue should work. I used a hot glue gun to secure the base to the center console of the car. The hot glue works well and can be removed without any damage to your car. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Console 12-Volt Accessory PlateC3D–01256
BMWConsole & storage

Console 12-Volt Accessory Plate

When I bought my e91 it had no front console cigarette lighter which meant I had to use an after market accessory plugged into the armrest socket. The unit was then wedged between the console and the passenger seat. Less than ideal. This plate fits in the ashtray hole and has a cut-out to accept an after market twin socket adapter which can be commonly found online or in value stores. I desinged this in sketchup and have included the SKP file in case anyone would like to remix it. Happy Printing Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Positive Battery Terminal CapC3D–01255
BMWCabin trim, cargo & roof

Positive Battery Terminal Cap

This is the cap for the positive battery terminal for a BMW E90. It should fit just about any BMW. Use automotive-rated wiring and connectors, retain fuse protection, insulate every terminal and verify unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Front-Wheel-Arch Headlight Access CoverC3D–01253
BMWExterior lighting, cameras & sensors

Front-Wheel-Arch Headlight Access Cover

Here I leave the headlight cover, located on the mudguard of the front wheel, is a piece very easy to lose and so I leave here the model to be able to print the fleeces own covers. Mine is already 1 month and I have not lost it or left, my BMW is an E91, but I think it serves in all E90 series. I leave the files in solidworks if they want to improve. Good impressions !! Greetings BMW Confirm body and lamp variant, secure retention, weather sealing and legal lamp operation before driving.

Fits 3 Series · E90 / E91 / E92 / E93

325i Clutch Alignment ToolC3D–01252
BMWInstallation & alignment jigs

325i Clutch Alignment Tool

This tool perfectly aligns the clutch friction plate for a BMW E90 325i with dual mass flywheel and self adjusting clutch. On the gearbox side of the tool there is a 7.1mm dia hole so that it can be tapped to M8. I recommend printing in PLA with 100% infill. Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

Fits 3 Series · E90 / E91 / E92 / E93

Bonnet Release HandleC3D–01251
BMWDashboard & controls

Bonnet Release Handle

I broke my bonnet release for my e92 so printed a new one with the BMW logo in it. It is considerably stronger if printed in PETG and it a perfect fit Use exterior-rated material and verify secure retention and adjacent-panel clearance.

Fits 3 Series · E90 / E91 / E92 / E93

Under-Seat Vent GrillesC3D–01250
BMWDashboard & controls

Under-Seat Vent Grilles

The BMW E92 has under-seat air-con vents which are prone to getting small objects kicked down them by rear seat passengers. Worse, there a small gap between them through which coins and the like can end up under the carpet where they then rattle annoyingly. Getting them out is a real pain an requires the seat, and possibly the speaker under it, to be removed. These simple grills clip over the vents preventing small objects going where they shouldn't. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Light Drain PlugC3D–01249
BMWExterior lighting, cameras & sensors

Light Drain Plug

The original plugs in the drain/vent of the e46 are cracking or missing, print a new one! Print it in TPU and install in the car. May be compatible with other cars of the brand but i didn't have others to try. Verify secure retention, weather sealing and legal lamp operation before driving.

Fits 3 Series · E46

coin holder trayC3D–01241
BMWConsole & storage

coin holder tray

This tray replaces the rubbery insert in the coin holder trim on the E46. Mine had begun to degrade, looking waxy and crumbling. I printed this from 85A TPU to replace it. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Floor Mat Retention ClipC3D–01240
BMWCabin trim, cargo & roof

Floor Mat Retention Clip

Got tired of the Velcro pads failing constantly, forcing me to adjust the floor mats every damn time I got in the car. This is my solution. Printing: Small part, so go 100% infill @ .2 or smaller Button face down Organic supports on crossmember PETG pref Install: Remove existing Velcro pads. Align floor mats. Eyeball orientation and location of vertical slot through carpet. Large swiss army knife blade is more or less perfect height. Cut a vertical slit through the carpet into corresponding chassis slot. Pass clip through carpet, into retention slot, and use a nickle/quarter to lock the clip into place. vroom vroom. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

repair wheel for the armrest jointC3D–01239
BMWWheels, plates, towing & roof equipment

repair wheel for the armrest joint

I created this repair wheel for the armrest, since it most often breaks or cracks in the joint, this wheel is installed and inserted in the place where the spring was originally. (and stick there) Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Switched 12-Volt Ashtray InsertC3D–01234
BMWDashboard & controls

Switched 12-Volt Ashtray Insert

Replacement ashtray insert with space for a switch that disconnects the E46 always-live cigarette-lighter outlet. The creator documents the physical insert, wiring and installed switch. Use an automotive rated switch and protected wiring, retain correct fuse protection, insulate every terminal and confirm the ashtray closes freely.

Fits 3 Series · E46

Touring Trunk Caddy BracketC3D–01232
BMWCabin trim, cargo & roof

Touring Trunk Caddy Bracket

These are brackets to mount an oddments tray (part no 51478230573) that is used in sedans instead of CD changer in the trunk. The brackets allow mounting the caddy in touring as well. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

LHD Ashtray USB HolderC3D–01231
BMWDashboard & controls

LHD Ashtray USB Holder

Filament: ASA Supports: Yes (As Applicable) Infill: Minimum 15% Brim: Yes (As Applicable) Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Coupe Front Speaker Reduction AdapterC3D–01229
BMWCabin trim, cargo & roof

Coupe Front Speaker Reduction Adapter

Front-door reduction adapter physically used in an E46 325Ci Coupe to install a 5.25-inch Kicker speaker in the factory 6.5-inch position. The source shows the printed ring, driver assembly and door fitment. Use sealing foam as documented and verify cone, magnet, wiring, window and door-trim clearance before fastening.

Fits 3 Series · E46

Boot handle fixC3D–01228
BMWDoors, bonnet, boot & bed hardware

Boot handle fix

Print these to fix the broken boot handle on your BMW. Theyre designed so they squeeze in the holes, creating some tension to be able to screw the handle to the car. The “center” ones are for the 2 center bolts, the “side” ones for the outer ones. Fits nice and neat on my 2003 e46 Touring, may need some slight adjusting but worked well enough for me. Use exterior-rated material and verify secure retention, sealing and adjacent-panel clearance.

Fits 3 Series · E46

Pioneer GM-D1004 Amplifier BracketC3D–01227
BMWCabin trim, cargo & roof

Pioneer GM-D1004 Amplifier Bracket

This bracket allows to mount the Pioneer GM-D1004 amp in place of the factory amp in the trunk. I used PETG and it works fine. Put some automotive Tesa tape on the metal ears before sliding the bracket to dampen vibrations. If You are missing a mounting screw or nut here are the codes: 07119902932, 61131372033. Fuse and insulate any added wiring correctly, secure it from chafe and confirm the circuit remains serviceable.

Fits 3 Series · E46

Roof Rails Replacement PartC3D–01226
BMWWheels, plates, towing & roof equipment

Roof Rails Replacement Part

When I bought some roof rails, the flaps for the screws to not scratch the paint had been broken off. So I threw this quick redesign together. It's mostly a replica with slight adjustments for better printing. DO NOT USE PLA, PETG, OR ABS You should consider a high-quality, very weather and outdoor-resistant filament. I used CPE CF112. Alternatives may include PA CF12 or PP. Print slow. Low to no fan. The chamber should be at least 40°C for best layer adhesion. Works best with 100% infill. Sadly I could not find the specific part number for this, I've heard a simple washer should do just as well. However, I'd like to keep it as original as possible with this, as it also helps with alignment. Use exterior-rated material and verify secure retention, sealing and adjacent-panel clearance.

Fits 3 Series · E46

Compact Front 165 mm Speaker AdapterC3D–01223
BMWCabin trim, cargo & roof

Compact Front 165 mm Speaker Adapter

Front-door adapter for installing a 165 mm speaker in the E46 Compact, whose factory speaker differs from other E46 bodies. The creator documents the original door, factory speaker, printed adapter and finished installation. Dry-fit before fastening and verify glass, wiring, cone and door-trim clearance through full window travel.

Fits 3 Series · E46

N42 86 mm Oil-Filter Housing WrenchC3D–01222
BMWService tools

N42 86 mm Oil-Filter Housing Wrench

Sixteen-flat 86 mm service wrench for the oil-filter housing on E46 models with the N42B18A engine, designed for a 12.5 mm square drive. The creator shows the physical tool on a ratchet. Use a strong heat-resistant material, keep the wrench fully seated and follow the BMW service torque for the housing cap.

Fits 3 Series · E46

Wiper clipC3D–01221
BMWWipers & washers

Wiper clip

So I broke my wiper clip while replacing some other stuff on the car. There's not really a viable/economical replacement and original part does not take well to super glue. I started from another STL and modeled over it in fusion. Then did a couple of test prints and iterated as I went. Depending on your tolerances, filament, and shrinkage, you may have to fiddle with the final dimensions. Printed in PC-ABS. It doesn't fall off when using the windshield washing function. idk if I'd use it in a rally race. Use at your own risk. Use heat-, UV- and fluid-resistant material and verify full wiper or washer clearance.

Fits 3 Series · E46

Magnetic Rear-Seat ISOFIX CoverC3D–01220
BMWSeats & restraints

Magnetic Rear-Seat ISOFIX Cover

Isofix cover for BMW E46 I was missing one of the isofix covers so I modeled and printed this one. It's not a perfect copy since I added a bit of thickness in some parts to make it stronger. You can see in one of the images the differences between the original and the 3d printed part. For this one the ABS filament is required since the PETG & PLA are not rigid enough. Added a magnetic version, magnet can be glued in place, 20 x 10 x 3 mm magnet size. This alleviates the need to print the part in ABS for strength. Print Settings Printer: TwoTrees Bluer Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Filament: Generic ABS Black Notes: Category: Automotive Confirm seat movement, belt access and occupant clearance before use.

Fits 3 Series · E46