car3dparts.

1997–2006

3 Series E46

Verified catalog fitment for this exact BMW generation. 87 printable parts currently match.

Facelift Side-Repeater Contour SpacerC3D–01148
BMWExterior lighting, cameras & sensors

Facelift Side-Repeater Contour Spacer

Contour spacer demonstrated with aftermarket side repeaters on BMW bodywork. The creator lists E36 from October 1996, E46 sedan/Touring, E60/E61, E81/E82/E87/E88 and E90–E93 applications. Test one side before mirroring and verify the repeater remains weather-sealed and positively retained.

Fits 1 Series · E81 / E82 / E87 / E88 · 3 Series · E36 · 3 Series · E46 +2

76 mm × 14-Flute Oil-Filter Cap WrenchC3D–01092
BMWService tools

76 mm × 14-Flute Oil-Filter Cap Wrench

Printed cap wrench for the 76 mm, 14-flute oil-filter housing associated with BMW 11421715960. The creator physically demonstrates the tool and lists E30, E36, E46, E34 and Z3 applications; confirm cap size before applying torque.

Fits 3 Series · E30 · 3 Series · E36 · 3 Series · E46 +2

M54B22 Intake Smoke-Test AdapterC3D–01245
BMWEngine & intake

M54B22 Intake Smoke-Test Adapter

80 mm intake adapter for vacuum or smoke leak testing on the E46 M54B22, designed around a standard automotive valve and physically demonstrated on the engine. Use only at low diagnostic pressure, keep foreign material out of the intake and remove the adapter before starting or driving the vehicle.

Fits 3 Series · E46

vent 52mm gauge podC3D–01233
BMWDashboard & controls

vent 52mm gauge pod

We did 6 different version to get it in the angle that it faces the driver. We had a tight fit so it did not need any mounting to the dash, but maybe some glue or other adhesive wouldn't hurt. Printed flat down on the surface, with ABS+ to resist the summer heat in the car. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Curved Gutter-Trim ClipC3D–01204
BMWBody panels & exterior trim

Curved Gutter-Trim Clip

Print standing vertically, Coat with a clear Just glue on your trim and push it on Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Grille and License-Plate GrommetC3D–01117
BMWBumpers, grilles & guards

Grille and License-Plate Grommet

Replacement plastic grommet used at E30 grille and rear license-plate mounting points, physically compared with the original. The creator also lists E36, E46, E90 and E92 applications; BMWFans confirms grommet 51131840154.

Fits 3 Series · E30 · 3 Series · E36 · 3 Series · E46 +1

Glovebox Damper PinC3D–01085
BMWConsole & storage

Glovebox Damper Pin

Dimensioned replacement glovebox damper pin for BMW E21, E28, E30, E31, E34, E38, E39, E46 and E60/E61. The creator identifies BMW pin 51161828956 and shows the physical result installed. Verify damper eye and panel thickness before fitting.

Fits 3 Series · E21 · 3 Series · E30 · 3 Series · E46 +6

Battery Retaining SpacerC3D–01352
BMWEngine-bay electrical & sensors

Battery Retaining Spacer

Battery-retaining spacer reproduced from BMW component 61211350825 for E30, E34, E39 and E46. BMWFans identifies it as spacer 1350825 and confirms those chassis among broader BMW usage. Match battery size, tray slot and hold-down engagement, and do not use it to compensate for an incorrect battery or damaged clamp.

Fits 3 Series · E30 · 3 Series · E46 · 5 Series · E34 +1

rear carpet cover broken clip holder repairC3D–01243
BMWCabin trim, cargo & roof

rear carpet cover broken clip holder repair

Doorstep broken clip holder part replacement. Designed to have large surface area for glue to properly hold it. I have also designed the clip, check my other designs. Print with 5+ walls vertically oriented , and glue it on the bracket with 2 component glue for best results. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Sun Visor ClipC3D–01224
BMWCabin trim, cargo & roof

Sun Visor Clip

Print a cheap replacement for OEM E46 sun visor clips. I recommend printing at 100% infill to prevent splitting at layers when installed. I had good success with a 98A TPU filament at 100% infill with supports on. Just give extra support spacing with TPU and use a torch after to lightly clean up any strings. Wouldn't recommend PLA due to the high temperature that the inside of vehicles can see during the summer heat. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

cap nut for engine coverC3D–01219
BMWEngine & intake

cap nut for engine cover

This is a nut for the engine cover as seen in the second image. It works for e46 316i,318i and 320i, possibly for other models that have the same nut. Note: you will need an O-ring or rubber washer (⌀10mm) to prevent unscrewing due to the engine vibrations, the original nut has one too. You'll need ABS filament or PET-G, PLA filament will break after a couple of months. Print Settings Printer Brand: Artillery Printer: Artillery Hornet Rafts: Yes Supports: No Resolution: 0.2 Infill: 25 Filament: ABS or PET-G Notes: minimum 3 perimeter for Vertical shells Category: Automotive Use the specified automotive-grade material, keep the tool square and inspect the serviced component before reassembly.

Fits 3 Series · E46

Positive-Terminal Base CoverC3D–01190
BMWEngine-bay electrical & sensors

Positive-Terminal Base Cover

Mine got lost, so I decided to make one! Print in PETG or other heat resistant filament. BMW (E46 3 Series, E83 X3) Battery Positive Terminal Base B + - Cover Cap (61138371011) Fuse and insulate any added wiring correctly, secure it from chafe and confirm the circuit remains serviceable.

Fits 3 Series · E46 · 7 Series · E38 · Z3 · E36/7 / E36/8

Window Regulator BushingC3D–01187
BMWInterior doors & windows

Window Regulator Bushing

Repair bushing for the E46 and E53 window regulator, physically assembled and load-tested by the creator with an M6 thread. The creator warns that ordinary PLA failed in summer heat. Use heat-resistant automotive material, dry-fit before fastening, and verify glass, latch, wiring and trim clearance through full operation.

Fits 3 Series · E46 · X5 · E53

Door-Sill Trim ClipC3D–01186
BMWCabin trim, cargo & roof

Door-Sill Trim Clip

Replacement clip for the door-sill trim. The creator installed several copies and reports that they hold securely. Align the clip carefully during installation so it does not break while being pressed into place. Use cabin-heat-resistant material, dry-fit the part, and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Glovebox USBC3D–01181
BMWDashboard & controls

Glovebox USB

If you don't use the flashlight in your e46 BMW glovebox, here is a nice USB port adaptor that will plug right into the dash and give you two switched ports! I removed the center of the flashlight receptacle with a screwdriver and removed the pins, which are reused in the new adapter. Print both pieces, then wire two of these buck converters with 18AWG wire. There is not a lot of space, so you need to be delicate. Pin closest the the edge is negative. Solder the lead wires to the pins before inserting from the bottom - be careful not to insert too far. Push the assembled converter into the receptacle, push the female connector housing onto the back, plug in the wire from the car and re-inser Fuse and insulate any added wiring correctly, secure it from chafe and confirm the circuit remains serviceable.

Fits 3 Series · E46

Compact Parcel-Shelf Support PinC3D–01159
BMWCabin trim, cargo & roof

Compact Parcel-Shelf Support Pin

Left/right parcel-shelf support pin for BMW E36 Compact and E46 Compact, physically installed by the creator. BMWFans confirms the exact right support as 51468146708. Use a tough material and verify shelf engagement without overloading the side trim.

Fits 3 Series · E36 · 3 Series · E46

Fuel-Tank Screw-Cap WrenchC3D–01424
BMWService tools

Fuel-Tank Screw-Cap Wrench

Service wrench for the notched BMW fuel-tank screw cap used on E46, E60/E61, E63/E64, E65–E68, E83 and E53 vehicles. The creator tested the same interface on an R53 MINI and identified BMW screw cap 16116762417; BMW catalog cross-reference independently confirms that cap across the listed BMW chassis. The printed wrench is not the screw cap itself, so no OEM number is assigned. Use a stiff engineering polymer, hand tools only, and replace rather than reuse any visibly damaged print.

Fits 3 Series · E46 · 5 Series · E60 / E61 · 6 Series · E63 / E64 +3

Adjustable Clutch StopC3D–01322
BMWTransmission & drivetrain

Adjustable Clutch Stop

Adjustable clutch-pedal stop body for manual-transmission BMW E28 and other listed classic BMW chassis. Assembly requires an M10 screw, two M10 nuts, a 40 mm washer and a genuine-style rubber cap. Adjust only far enough to remove excess pedal travel while preserving complete clutch disengagement, then lock the nuts securely and re-check operation before driving.

Fits 3 Series · E30 · 3 Series · E36 · 3 Series · E46 +4

Light Drain PlugC3D–01249
BMWExterior lighting, cameras & sensors

Light Drain Plug

The original plugs in the drain/vent of the e46 are cracking or missing, print a new one! Print it in TPU and install in the car. May be compatible with other cars of the brand but i didn't have others to try. Verify secure retention, weather sealing and legal lamp operation before driving.

Fits 3 Series · E46

coin holder trayC3D–01241
BMWConsole & storage

coin holder tray

This tray replaces the rubbery insert in the coin holder trim on the E46. Mine had begun to degrade, looking waxy and crumbling. I printed this from 85A TPU to replace it. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Floor Mat Retention ClipC3D–01240
BMWCabin trim, cargo & roof

Floor Mat Retention Clip

Got tired of the Velcro pads failing constantly, forcing me to adjust the floor mats every damn time I got in the car. This is my solution. Printing: Small part, so go 100% infill @ .2 or smaller Button face down Organic supports on crossmember PETG pref Install: Remove existing Velcro pads. Align floor mats. Eyeball orientation and location of vertical slot through carpet. Large swiss army knife blade is more or less perfect height. Cut a vertical slit through the carpet into corresponding chassis slot. Pass clip through carpet, into retention slot, and use a nickle/quarter to lock the clip into place. vroom vroom. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

repair wheel for the armrest jointC3D–01239
BMWWheels, plates, towing & roof equipment

repair wheel for the armrest joint

I created this repair wheel for the armrest, since it most often breaks or cracks in the joint, this wheel is installed and inserted in the place where the spring was originally. (and stick there) Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Switched 12-Volt Ashtray InsertC3D–01234
BMWDashboard & controls

Switched 12-Volt Ashtray Insert

Replacement ashtray insert with space for a switch that disconnects the E46 always-live cigarette-lighter outlet. The creator documents the physical insert, wiring and installed switch. Use an automotive rated switch and protected wiring, retain correct fuse protection, insulate every terminal and confirm the ashtray closes freely.

Fits 3 Series · E46